Site icon HOPNHATCO

Máy nén khí trục vít nam châm vĩnh cửu TPM

admin

Product Advantages

Permanent magnet motor

The motor IP54 and the main engine share the same shaft, without coupling, central bracket, belt, gear, etc. The transmission efficiency is 100%, whose efficiency is 5-12% higher than that of the same capacity asynchronous motor. The motor is bearingless and oil sealed, eliminating routine maintenance and repairation. The volume is half smaller than the main component of ordinary three phase motor, and the weight is one-third lighter than that of the common motor host component.

Frequency inverter

Frequency conversion operation, start smoothly and stably with low noise. The large reduction of the starting current reduces the maximum power load, so as to save a lot of electricity. The demand of compressed air is varied every time depend on loading condition and the fluctuation rate is 40 – 80%. With application of Inverter Control system, the compressed air can be produced accurately according to the demand. And eventually, it can make much energy saving compared to normal compressor.

Intelligent control

Through higher intelligent control, the size of air production can be adjusted automatically, therefore, no matter how the air volume fluctuates, the pressure is always maintained which means the operation is really under constant pressure. The motor responds quickly, starts quickly and loads quickly.When the air volume is suddenly changed, it can respond quickly and the reaction time is within 50ms. It completely avoids the damage of uers’ equipment and product defects caused by the pressure tuation, moreover, it reduces the energy loss caused by the pressure fluctuation.

Energy Saving Airend

Energy Saving Airend (using 6 SKF bearings)
With new and exclusive design of Typhoon screw rotor which has been passed through the accurate machining procedure and test, it improves efficiency of airend and optimizes the airflow. We use a set of opposite biconical roller bearings at the end of exhaust end enable to support thrust load effectively and extend the running time.

Energy Saving Intake Valve

Intake valve have function of proportional adjusting the air inflow, according to user’s air demand, intake volume can be adjusted from 0-100%.
With non-return function,
With air-bleeding function,
With no-load delay function

High capability cooling system

Using axial fan, large propeller, lower speed and lower noise. With high air pressure, high air volume and stable operation.
Large heat exchanger, using high strength aluminum alloy material, ensure good cooling effect even under 45 degree environment.

Product Parameter

TPM SERIES TECHNICAL SPECIFICATION
Model Power Pressure Capacity Dimensions Weight Outlet Pipe Noise Level
KW HP bar M3/min (LxWxH) mm Kg Diameter dB
TPM7.5A 5.5 7.5 7 0.90 840x670x925 200 G3/4 65
8 0.80
10 0.70
13 0.60
TPM10A 7.5 10 7 1.05 840x670x925 200 G3/4 65
8 1.10
10 1.00
13 0.80
TPM15A 11 15 7 1.68 1000x820x1145 300 G3/4 65
8 1.60
10 1.45
13 1.30
TPM20A 15 20 7 2.50 1000x820x1145 300 G3/4 65
8 2.30
10 2.00
13 1.74
15 1.50
TPM30A 22 30 7 3.52 1100x880x1190 390 Gl 1/4 75
8 3.36
10 3.06
13 2.80
15 2.20
TPM40A 30 40 7 5.20 1200x950x1358 530 Gl 1/4 75
8 4.72
10 4.30
13 3.90
TPM50A 37 50 7 6.51 1300x1000x1366 590 Gl 1/2 75
8 6.19
10 5.62
13 5.10
TPM60A 45 60 7 7.71 1300x1000x1366 590 Gl 1/2 80
8 7.35
10 6.67
13 5.80
TPM75A 55 75 7 10.14 1600x1300x1600 1210 G2 80
8 9.66
10 8.77
13 7.95
TPM100A 75 100 7 13.50 1600x1300x1600 1210 G2 80
8 12.51
10 11.21
13 9.78
TPM120A 90 120 7 14.91 1600x1300x1600 1220 G2 85
8 14.17
10 12.88
13 11.50
TPM150A 110 150 7 20.96 2090x1550x2000 2300 DN65 85
8 20.06
10 17.02
13 15.30
TPM175A 132 >175 7 23.37 2090x1550x2000 2300 DN65 85
8 22.50
10 21.03
13 18.00